Scriber set - 4 pieces Different shapes hooks

Carbide steel bur - Arch pointed nose 3,2x38mm Industry Quality Ideal for Proxxon, Dremel and comparable machines with a 3,2mm collet

Microscale Micro Sol - Decalfluïd Micro Sol setting solution is for the most difficult irregular surfaces to be found on models. It completely softens the Microscale Decal, allowing it to drape down onto the surface of the model, conforming perfectly to

Microscale Micro Set - Decalfluïd Micro Set is a very versatile decal setting solution that does several things to Microscale Decals to improve application. Micro Set should be applied to the surface of the model where you will be sliding the decal off t

Humbrol Maskol Humbrol Maskol is a liquid. when dried it looks like a kind of rubber film. This allows you to easily protect parts of your model when you are going to paint or for example want to apply camouflage. It is recommended not to leave the dried

Triangle screwdriver bit set 1.8mm / 2.0mm / 2.3mm /2.7mm /3.0mm often used to remove base plates from scale model cars

Single blade nipper Premium cutting pliers, very thin. Only for plastic up to 3mm. Has a sharp and a flat side so that parts can be cut out of the sprue with high precision

Tweezer support / holder clamp Adjustable support, for cross tweezers

Photo Etched parts Bender (Large) with 4 bending aids. Has been specially developed for model building using photo etch parts allowing the brass to be held and bent accurately into many different shapes. Measures 79mm x 162mm

Mini Anvil Double horn anvil for precision work. Excellent quality. hardened. Widely used by watchmakers, jewelers and hobbyists.

Nail press 2mm / 3mm A nail press is the solution if you need to hammer small nails and nails into a delicate surface. Or if it is dangerous to use a hammer. The nail press has a magnetic head that holds the nail in place. Make your choice: Blue - for nai

Watchmakers tap set Taps and die in the following sizes: 0,7mm / 0,8mm / 0,9mm / 1.0mm / 1.1mm / 1.2mm / 1.3mm / 1.4mm / 1.5mm / 1.6mm / 1.7mm / 1.8mm / 1.9mm / 2.0 mm Holes should be pre-drilled 0.1mm smaller. Taps can be clamped in a drill chuck, for ex

Watchmakers tap set Taps and die in the following sizes: 0.6mm / 0.7mm / 0.8mm / 0.9mm / 1.0mm Holes should be pre-drilled 0.1mm smaller. Taps can be clamped in a drill chuck, for example: https://www.marks-miniatures.com/en/hand-drill-with-chuck-and-rota

Mini vise Jaw width 40mm Maximum opening: 30 mm Can be mounted on the table with the screw holes.

spring clamp Maximum opening: 35 mm The clamp opens by squeezing. When released, the clamp closes automatically. Suitable for clamping different shapes. (round, square, triangle etc,)

Spare soldering tip for Soldering Station D12-1 Choose from soldering tip: 1 Fine 2 Medium 3 Large

Solder tin wire - 0.5 mm, lead free Sn 99.3 Cu0.7 - Rosin Core 10 gram

Solder tin wire - 0.6 mm, 100 gram 60/40 Rosin Core 100 gram

Solder tin wire - 1mm 60/40 Rosin Core 17 gram

Miter sanding aid - angle sanding The angle can be adjusted. The handpiece has a slide (stop). Comes with a set of 3 extra sanding belts: 150 Grid 240 Grid 320 Grid Sanding belt set is also available separately. Ideal for profiles in styrene, wood and me

Saw help for tubes and rods

Photo Etch Pencil Has a slightly sticky tip, to pick and place small parts without shooting away. If the tip is not sticky or sharp anymore it can be scharpened with a regular pencil sharpener.

Flat brush

Extra long mini Drill Set 0.5/0.7/1.0/1.5/2.5mm Approx. 100 mm long